How to make an industrial Training report of internship

Today I want to tell you about industrial training report

Sequence, information, pattern

Steps1

1) first page of your report is your college logo and name and you also add your faculty mentor.

Step2

2) logo and name of company where you done your internship.

Step3

3) certificate

Acknowledge

Abstract

Step4

4) introduction of company which is available on company website and company ISO file.

Step5

5) Machine used in industry

Write the name of machines which is available In industry include with their specifications , identification number, cost and Maintenance etc.

Step6

6) Measuring instruments used in industry

List the instrument name which is available in industry with their specifications, purpose, cost and Maintenance etc.

Step7

7) Manufacturing process used in industry

Write the complete manufacturing process of industry.

Step 8

8) Quality check Method

Write quality check Method of raw materials.

Ultrasound is also a method in which material can be check whether it is good mechanical strength or not.

Step9

9) Type of products

List the name of products which industry produce.

Step10

10) challenging Experience

Write which type of difficulty you face during training.

Step 11

11) safety precautions

Step 12

12) References

In reference you can add iso file of company, faculty mentor name and company website

This is the procedure to make industrial Report.

To understand more better watch my video on YouTube and subscribe our channel.

I hope you understand more better in this video

Comments

And

subscribe our channel

Thank you

Comments

Nuclear Power plant project Report

General Layout of Nuclear Power Plant- The Main components of a NUCLEAR POWER PLANT are :- Nuclear Reactor Heat Exchanger ( Steam Generator ) Steam Turbine Generator Steam Condenser Cooling Tower Coolent Pump Basic components of Nuclear power plant are :- Nuclear Reactor :- It is the heart of the nuclear power plant. In nuclear reactor, nuclear fission of radioactive material takes place. This generates large amount of heat energy. This heat is taken by the coolent circulating through the reactor core. After absorbing the heat, the coolent becomes hot. Heat Exchanger ( Steam Generator ) :- The hot coolent coming from nuclear reactor flows through tubes of heat exchanger. In heat exchanger, hot coolent gives up heat to feed water so that it can be converted into steam. After giving up heat, the coolent is again pumped back to nuclear reactor. Steam Turbine :- Steam produced in heat exchanger is expanded in steam turbine to produce mechanical energy. Generator :- Output shaft ...

Mostly Asked Questions in interview about vernier caliper

Every Engineer should know this thing about vernier Today I will share a interview experience in which I face the question and answer related to vernier caliper. First of all it is necessary to know who invent the vernier caliper so pierre vernier invented. Then they will asked you 1)What is least count ? 2)What is range and resolution of Vernier caliper? 3) what is calibration of vernier caliper? 4) if error occurs in vernier caliper then how to correct it or Recalibrate it? This was the question which is asked in interview which is explained in detail in below video. Go to my YouTube channel and watched this video I hope your all doubt will be clear after watching this video. Subscribe our YouTube channel below link and clear more doubt https://www.youtube.com/channel/UCO7dCM3Lv8XFAbXkquqZt8Q

STUDY OF DRUM BRAKE

What is drum brake? A drum brake is a brake that uses friction caused by a set of shoes or pads that press outward against a rotating cylinder-shaped part called a brake drum. The term drum brake usually means a brake in which shoes press on the inner surface of the drum. When shoes press on the outside of the drum, it is usually called a clasp brake. Where the drum is pinched between two shoes, similar to a conventional disc brake, it is sometimes called a pinch drum brake, though such brakes are relatively rare. A related type called a band brake uses a flexible belt or "band" wrapping around the outside of a drum. Components:- 1. Backing plate 2. Brake drum 3. Wheel cylinder 4. Brake shoes. Backing plate The backing plate provides a base for the other components. The back plate also increases the rigidity of whole set-up, supports the housing, and protects it from foreign materials like dust and other road debris. It absorbs the torque from the braking action, and that is ...

Mechanical Marks Study

Search This Blog